Welcome to Steiner Tractor Parts

    1 - 9 of 9 Products >
  1. Oliver 77 Rear Main Seal
  2. >
  3. all
Refinement Options

By Price

Oliver 77 Rear Main Seal

  • 1
Sort by:
View: Show: per page
Showing Products: 1 - 9 Total Products: 9

Ball Bearing

…used: 66, 660, 77, 770, 88, 880, Super 66, Super 77, Super 88, Fits following as a clutch shaft pilot bearing (not sealed), 1 used: 28-44, 70, 90, 900, 99, Fits following as a top transmission main shaft bearing, 2 used: 440, Super 44, Fits following as a top transmission main shaft rear bearing, 1…

Product Number: ABC3437
Price: $5.20

USA Made - Antique Tractor Blog

…* Minneapolis Moline * Oliver * Contact Us * Tractor Parts * Home * Farmall / International * Engine Parts * USA Made USA Made 01/03/2014Written by Suzette Thomas Leave a Comment Replace your leaking rear main seals on your International tractor with our new crankshaft seal kits. Made in the USA,…

Iowa State University - Project Update - Antique Tractor Blog

…University on their Oliver 880. I just wanted to present you with an update on the tractor before we finish up first semester. Mainly because I think it is important to show you how far we are going into this tractor to make this a complete restoration. The tractor is mainly in pieces and our first…

Tractor Story - CASE VAC - Antique Tractor Blog

…3 Comments * Doug 02/07/2017 - 22:54 Can anyone shed some light on changing the differential brake shaft carrier seal on a Case VAC with rear disk brakes. I found the replacement seal, have the schematic, have the brake cover and disk removed as well as the four bolts in the inner cover. however,…

Related Products: Case Vac | Case Vac Clutch

How to determine 9N from 2N Ford tractor. - Antique Tractor Blog

…rods (mid year). * Sealed beam headlights first offered. 1945 2N * Heavier rear axle housings introduced (mid year). 1946 2N * Rear axle housings are improved by making them thicker again. 1947 2N * Casting number and date added to engine block (where starter bolts) to rear axle housing. For more…

Related Products: Ford 9n Starter Switch

Tractor Story - Ford 8N - Antique Tractor Blog

…Story – 1940 John Deere Styled B 1 Comment * Tim Powell 11/07/2018 - 16:19 I had a machine shop restore my 1952 Ford 8N. Now front and rear engine seals leak oil. what could be the problem, incorrect installation? Reply Leave a Reply Cancel reply Your email address will not be published.…

Shop Mule - Antique Tractor Blog

…restoring. It uses the same International tranny and rear end but uses a Buda 4b-153 engine. I’m in serious need of some axle seals if anyone knows where to get them. Reply * Ed Warns 08/03/2018 - 12:03 I’m looking for axle seals also. I have an Allis Chalmers TG24. Reply * Suzette Thomas…

Farmall Cub ~ Think Pink - Antique Tractor Blog

…bushings, bearings, seals, and gaskets everywhere we could find them. The tractor and parts got sandblasted to give us some bare metal. We painted the tractor in primer and then that beautiful red with hardner in it to make the paint better than when new. We added lights and rear wheel weights. We…

Ferguson Tractor Identification - Antique Tractor Blog

…Steering Wheel Cap 11 Comments * John Rutherford 06/23/2015 - 20:50 I own a 1954 Ferguson TEA20 tractor that requires rear fenders, Steering box bronze bushings and oil seals. Also points, condensor, and rotor, Voltage regulator. May need some more parts before I’m finished restoring the…

Did you find this search useful? Yes No
  • 1
Sort by:
View: Show: per page