Please try logging in using your email address and password from the old site. If you had issues on 11/15, those should be resolved now, 11/16. Thank you for your patience!
…This fuel sending unit is properly calibrated to the original resistance, 0 to 30 OHM`s. Use with our original style fuel gauge, JDS1707 or JDS1910 or JDS3476 depending on voltage.* For maximum performance it is always best to order the fuel sending unit and the matching fuel gauge…
…4040, 4130 4 cylinder (Following 4 cylinder gas, diesel 1958 - 1964) ] * This fuel sending unit will work with FDS275 and FDS276 fuel gauges sold by Steiner Tractor Parts.* It does not work with the OEM fuel gauges.* This fuel sending unit measures 8-3/4" long.* It has a 14 - 122 Ohm Range.
…1958 - 1964) ] * 6 volt* Positive Ground* Black raised bezel* 14 to 122 ohm range. Will work with our FDS199 and FDS200 Fuel Sending units. This gauge must be grounded to work properly. In some cases, you may have to run an extra ground wire from the threaded clamp…
…only.* For diesel pony start tractors only.* Use w/ fuel sending unit # JDS1712* For maximum performance it is always best to order the fuel sending unit and the matching fuel gauge as they will have the correct Ohms and voltage.* Gauge must be grounded to work properly, In some cases you…
…Star Super (WITH CLOCKWISE TACHOMETER & 12V SYSTEM, BOTH GAS AND DIESEL) ]; Replaces: FUEL GAUGE TANK UNIT / FUEL SENDER: 10A7696, TACHOURMETER AND SPEEDOMETER ASSEMBLY: 10A8102, FUEL GAUGE: 10A8104, GAUGES TO INSTRUMENT PANEL GASKET: 10P1320, MOLDING: 10P888, INSTRUMENT PANEL GLASS: 10P889,…
…- Fits: 2030, 2130 * This fuel sending unit will work with FDS275 and FDS276 fuel gauges sold by Steiner Tractor Parts.* It does not work with the OEM fuel gauges.* This fuel sending unit measures 5-1/2" long.* It has a 14 - 122 Ohm Range.* Fits Gas and Diesel.* Use w/ FDS178 fuel tank.
Replacement of a fuel gauge and sending unit by Tyler Buchheit on a John Deere 630. These steps apply to the John Deere 20 or 30 series tractors.
…840, 850, 860, 900, 950, 951, 960 (gas models 1953 thru 1964 for 6 volt generator systems only) ]; Replaces: FDN14401B Includes main harness, light wires, ignition switch and instruction sheet. Does not include fuel gauge or sender wires. This wiring harness is for 6 volt generator systems only.
…12 volt positive ground (0-30 Ohms) electric fuel gauge & JDS1712 USA made fuel sending unit fits 520, 530, 620, 630 GP, Standard, Orchard, 720, 730 2-cylinder. The fuel gauge also fits 820, 830 2-cylinder. Order today! John Deere fuel gauge, JDS1707, JDS1712, john deere, new parts for old…
…without fuel gauge (1953 - 1957). If customer has a fuel gauge, you must reuse the gauge and sending unit wires) ]; Replaces: FDN14401B * For 6 volt systems only* Original style braiding* Soldered terminals* Does NOT Include: spark plug wires, battery cables, fuel gauge and…
…by Suzette Thomas 1 Comment Check out our line of restoration quality gauges for IH/Farmall tractors from 1939 to 1946. Each gauge has the same faceplate as the original design including the IHC logo. Not only do our gauges look good, they will keep your engine, oil pressure, and water temperature…
…controlled explosion machines. Fuel fills the combustion chamber and is ignited by the spark. The force of this explosion moves the pistons, the pistons move the crankshaft, and so on. More fuel will make a difference in the amount of output, since more fuel means a bigger (more powerful) explosion.…
…the other side or under the regulator. * Cub mounts below the generator on governor housing, others mount on back of the light switch box or rear fuel tank support. * Also note that “from the factory” regulators were never mounted on the generator. * Other models’ regulators have…
…Instructions IHS486 – Farmall M (with regulator on steering post, under fuel tank, sn FBK 229911 and up), Early Super M (sn F501 – F28174 and sn L500001 – L504801 Gas) WITH BATTERY BOX UNDER FUEL TANK Wiring Harness Instructions IHS487 – Farmall FITS FOLLOWING WITH BATTERY…
…lever left of driver * Cast iron frame * Round front axle * Radiator bolts directly to front support casting (No lower tank) * Hydraulics under fuel tank * Foot platform offset to right side * ‘Rod’ style throttle linkage * Headlights attach to front radiator side plates …