Welcome to Steiner Tractor Parts
Fits John Deere - [ 3010, 3020, 4000, 4010, 4020 (Fits tractors with 69 series Zenith carburetor and side mounted solenoid or load nozzle) ], 500 Carb Mfg #'s - 12506, 12510, 12879, 13320, 13429, 13430, 13924
JD Industrial - Fits: 440 (With listed Marvel Schebler carburetors) Fits John Deere - [ M, 40, 420, 430 (With listed Marvel Schebler carburetors) ] Marvel Schebler - Replaces: 43-613, 43-622, 43-678, 43-699 Minneapolis Moline - Fits: KT, MT, ZAE, ZAN, ZAS, ZAU, ZB, ZBE, ZBN, ZBU, 445; Replaces:…
…SO, VA, VAC, VAI, VAO, 400, 570 (Used as an adjustable load nozzle assembly to eliminate the electric solenoid when used on Zenith 13783 carburetors. ); Replaces: B51326 Case Industrial - Fits: [ 1845, 580B, 580 Loader (Used as an adjustable load nozzle assembly to eliminate the electric solenoid…
Cockshutt - Fits: 550 (Oliver Built Only) Ford - Fits: [ 4000 4 cylinder, 4031, 4110, 4120, 4121, 4131, 4140, 801, 811, 821, 841, 851, 861, 871, 881, 901, 941, 951, 961, 971, 981 (1957 - 1964 with 172 Cubic Inch engines and with Marvel Schebler TSX662, TSX769, TSX774, TSX813) ]; Replaces: 311605,…
…fits TSX464, TSX561 or TSX773 * choke plate* throttle shaft bushings and packing * metering nozzle * load adjusting nozzle* brass plugs* float pin * needle and seat * drain petcock* gaskets* & more...Note: Our kit also fits carburetor…
Fits John Deere - [ 3010, 3020, 4000, 4010, 4020 (Fits tractors with 69 series Zenith carburetor and end mounted solenoid or load nozzle) ]; Replaces: AR46109, Washer: H21058, Packing: R13069, R13070 Carb Mfg #'s - : 12506, 12510, 12879, 13209, 13320, 13429, 13430
…blade and replace it if it is bent, cracked, has loose rivets or broken welds. Imbalance in the fan can cause excessive load on the water pump bearing and seal. B) Never adjust a fan belt tighter than factory specifications. C) Inspect the radiator cap. If it looks corroded, it is wise to purchase…
Fits John Deere - [ B, BN, BNH, BW, BWH, BWH40 (Styled, with DLTX67, DLTX73 carburetor) ]; Replaces: (1) Idle adjusting screw: 21H994R, (1) Carburetor to manifold gasket: 321R, (1) Load needle: AR10018R, (1) Idle needle: AR10020R, (1) Strainer assembly: AR10021R, (1) Throttle shaft: AR10058R, (1)…
…John Deere - [ A, AH, AN, ANH, AO, AR, AW, AWH (Late, using DLTX71 and DLTX72 carburetors) ]; Replaces: (1) Idle adjusting screw: 21H994R, (1) Carburetor to manifold gasket: 321R, (1) Load needle: AR10018R, (1) Idle needle: AR10020R, (1) Strainer assembly: AR10021R, (1) Throttle shaft: AR10058R, (1)…
Fits John Deere - [ A, AH, AN, ANH, AO, AR, AW, AWH (with DLTX24, DLTX53 carburetors) ]; Replaces: (1) Carburetor to manifold gasket: 321R, (1) Load needle: AR10018R, (1) Idle needle: AR10020R, (1) Strainer assembly: AR10021R, (1) Choke shaft & lever: AR10043R, (1) Drain petcock: AR10075R, (1)…
…drafty shop doesn’t necessarily equal a well-ventilated shop. Be aware of the fume buildup, especially if you normally work with the door open. Adjust your habits accordingly – either save the tasks that need ventilation for spring, or bundle up and throw open the door. * Heat. Kerosene…
…explained. “If I took it out of the van, it was a better deal.” Dan loaded up the motor and started dreaming on his way back home. Unlike a flatehead V8, Dan found that the V6 fit inside his 1951 8N without any structural adjustments – the hood and tie-rods remained the same. Dan upgraded to a…
…wasn’t set right, and put the carb back on after a little bending. We tried starting it again and it would fire a few times, then after more adjustments it would run for 10-15 seconds. After more tweaking it ran like a charm. Since then I have replaced all fluids, installed a new sediment bowl,…