Pivot Pin

Fast Hitch Pin with Ball and Handle

…attach pin, 4 used) ], 230 (used as a float locking pin, 2 used), 330 (used as a lateral swing lockout pin, 1 used), 330 (used as a socket pivot lockout pin, 2 used), Farmall: 240 (used as a float locking pin, 2 used), [ 300, 340, 350, 400, 450, 460, 504, 560 (used as a socket pivot lockout pin, 2…
Product Number: IHS3069
Related Products: Fast Hitch Pin | Fast Hitch

Bolster Pivot Pin

International / Farmall - Fits: [ H, Hydro 70, M, MD, MTA, Super H, Super M, 1206, 1256, 400, 450, 460, 544, 560, 656, 666, 686, 706, 756, 806, 826, 856 ( with factory IH wide front) ], [ Farmall Rowcrop: 300, 350 ( with factory IH wide front) ]; Replaces: 358978R1, 358978R2 * 1-1/4" diameter*…
Product Number: IHS097

Yoke With Pivot For 3 Point Adjustable Upright

Fits John Deere - 520, 530, 620, 630, 720, 730 (INCLUDING HI-CROP); Replaces: 12H303, 14H785, 19H1901, 34H331, 34H369, AF2704R, B2804R, DA5883A, F2671R, F2673R, F2674R, F2675R, JD7759 Fits original John Deere three point hitch.
Product Number: JDS223
Related Products: 3 Point Hitch John Deere | 3 Point Hitch Parts

Bushing

IH Industrial - Fits: as a reverse idler gear bushing: I6, ID6 International / Farmall - Fits: Following as a WIDE FRONT axle pivot pin bushing for factory adjustable wide front axle and tie rods behind the axle: 1026, 1256, 400, 450, 660, 666, F300, F350, F460, F544, F560, F656, F706, F756, F806,…
Product Number: IHS4159
Related Products: Bushing | Ihs4159

Swinging Drawbar Pin

…4430 (up to SN: 21269); Replaces: AR32826, AR44189 Rotating handle allows pin to pivot for even wear of shaft. Early factory pins were welded which led to the pin wearing unevenly, and the handle often broke as the pin tried to rotate but the handle bound against the retaining bracket and snapped.*…
Product Number: JDS3734
Related Products: Drawbar Pin John Deere

Front Pivot Bushing

…TO30, TO35 (Straight bushing, not flanged, will fit some) ]; Replaces: 180344M1 * Please note: This is for the standard front axle. It will not work on heavy duty or industrial axles.* 1.770" inside diameter* 1-15/16" outside diameter* 1-1/2" long* Must be reamed / honed to size, to fit the pin.
Product Number: ABC379
Related Products: Ford 641 | Ford 601 | 8n Ford Parts

Draft Link Pivot Pin

Fits John Deere - [ 3010, 3020 (Up to SN: 81039) ], 720, 730, Industrial: 500 (Up to SN: 81039); Replaces: F2781R, R40516 * 2 used per tractor, sold individually* Yellow zinc
Product Number: JDS1641
Related Products: John Deere Lift Arm | John Deere 3010

Draft Link Pivot Pin

Fits John Deere - 520, 530, 620, 630; Replaces: A5715R
Product Number: JDS1639
Related Products: John Deere Lift Arm | John Deere 630

Clutch Pedal Pivot Pin

International / Farmall - Fits: [ 1026, 1206, 1256, 1456, 706, 756, 806, 826, 856 (Fit the following gear drive and HYDROs) ], 1066 (Fit the following gear drive and HYDROs,up to sn 17030), 1466 (Fit the following gear drive and HYDROs, up to sn 12145), 1468 (Fit the following gear drive and HYDROs,…
Product Number: IHS1364

Brake Pivot Pin, Toggle Pin

Allis Chalmers - Fits: B, C, CA, IB; Replaces: 207221, 70207221 * Zinc plated* 0.750"  diameter* 1.625" long* Pin is used with hand brakes and foot brakes
Product Number: ACS1650

Clutch Release Yoke Pivot Pin

International / Farmall - Fits: Cub, Cub LoBoy: Cub Loboy; Replaces: 350948R1 DO NOT START ENGINE WITHOUT CHECKING CLUTCH PRESSURE PLATE FINGER CLEARANCE, FAILURE TO DO SO COULD DAMAGE THE PRESSURE PLATE & THROW OUT BEARING, ADJUST CLUTCH LINKAGE PER INSTRUCTIONS. -------------(WILL NOT FIT 154,…
Product Number: IHS1497
Related Products: Clutch Linkage | Farmall Clutch Release Bearing | Farmall Cub Clutch

Drawbar Pivot Pin With Handle

Fits John Deere - [ G, GN, GW (sn 18700 and up) ], 620 (sn 6213100 and up), 630, 70, 720, 730; Replaces: AF1318R, AF3759R, F856R * Hardened steel* 0.765" OD* 2.8160" Overall Length
Product Number: JDS1147
Related Products: Drawbar Pin John Deere | John Deere Drawbar | Drawbar Pin

Seat Pivot Bracket Pin

…ID6 IH Miscellaneous - Fits: Windrower: 163 International / Farmall - Fits: H, HV, I9, ID9, M, MD, MDV, MV, O4, O6, OS4, OS6, Super W4, Super W6TA, Super WD9, W4, W6, W9, WD6, WD9, WDR9, WR9S, Cotton Picker: 214, 214A, 220, 220A, Windrower: 161; Replaces: Nut: 103026, Washer: 103321, Pin: 51292DA
Product Number: IHS1700
Related Products: Farmall M Seat

Drawbar Pivot Pin With Handle, 3 Point Hitch Draft Link Pin

…a drawbar pivot pin with handle), Special Standard: 40 (Used as a drawbar pivot pin with handle), Special, Semi HiCrop: 420 (Used as a drawbar pivot pin with handle), [ Standard: 40, 420, 430 (Used as a drawbar pivot pin with handle) ], [ TriCycle: 40, 420 (Used as a drawbar pivot pin with handle)…
Product Number: JDS1488
Related Products: Drawbar Pin John Deere | Drawbar Pin | Swinging Drawbar

Front Pivot Bolster Bracket

IH Industrial - Fits: 2404, 2424, 2444 International / Farmall - Fits: 240, 404, 424, 444; Replaces: Pin: 368604R11, Casting Number: 369008R1, 369008R5
Product Number: IHS457
Related Products: Ih 404 | Bolster | Ih 2404

Lower Front Pivot Bolster

International / Farmall - Fits: M, MD, MTA, Super M, 1206, 1256, 400, 450, 544, 560, 656, 666, 686, 706, 756, 806, 826, 856, Hydro: Hydro 70; Replaces: 383909R4 * For use on all models listed with the factory IH wide front.* Machined for 1.230" diameter pin.
Product Number: IHS055
Related Products: Farmall 706 | Farmall M Bolster | Bolster